Skip to content
CFM Limited logo

Maintenance

AdBlue, DPF and engine derates: what the dashboard is telling you

4 min read

An emissions warning light on a modern truck is a countdown, not a suggestion. Left alone it ends in a power derate and a vehicle that will not do the work, usually at the least convenient moment.

Why these systems exist

Euro VI vehicles clean their exhaust in two stages. A diesel particulate filter traps soot and periodically burns it off. Selective catalytic reduction injects AdBlue into the exhaust to convert nitrogen oxides into nitrogen and water.

Both are monitored constantly, and the law requires the vehicle to respond when they stop working properly. That response is deliberately designed to be something you cannot ignore — which is why a sensor worth very little can end up immobilising a vehicle worth a great deal.

The escalation, in order

The detail varies by manufacturer and emissions standard, but the sequence is consistent:

  1. A warning lamp, often amber, with no change in how the vehicle drives
  2. The lamp stays on and a countdown begins — by distance, by engine hours, or both
  3. Torque is reduced. The vehicle still moves but will not pull properly
  4. A speed limit is imposed, frequently low enough to make motorway work impossible

The important point is that stages one and two are free. Everything expensive happens because the first warning was carried for a fortnight.

DPF problems

A DPF needs to get hot enough to burn off the soot it has collected. Regeneration either happens passively on a long run, or actively when the engine injects extra fuel to raise exhaust temperature.

Work patterns are what usually break this. Short urban runs, a lot of idling, multi-drop routes, or a vehicle spending its day on site never get the filter hot enough, so soot accumulates faster than it burns. Interrupting active regenerations by switching off mid-cycle has the same effect.

By the time the filter is genuinely blocked you are often past a forced regeneration on the diagnostic equipment and into removal and cleaning, or replacement. Worth knowing: a blocked DPF is sometimes the symptom rather than the fault. A leaking injector or a turbo passing oil will fill a filter again within weeks, so the filter is not the end of the job.

AdBlue and SCR faults

AdBlue problems divide into three kinds:

  • Quality. AdBlue is a precise solution of urea in demineralised water. It degrades in heat, has a real shelf life, and is ruined by contamination — a funnel used for something else, or water from a jet wash, is enough. Quality sensors do detect this.
  • Delivery. Crystallisation around the injector or in the lines, pump failure, a blocked filter, or a tank heater that has failed so the fluid freezes in winter.
  • Measurement. NOx sensors, temperature sensors and level sensors all fail, and a healthy system with a failed sensor derates exactly like a broken one.

Cold weather is the seasonal pattern here. AdBlue freezes at around −11°C, which is what tank and line heaters are for — and a heater fault that went unnoticed all summer announces itself on the first hard frost.

What not to do

  • Do not have the system removed, bypassed or mapped out. It is an offence, it will fail the annual test, and it exposes the operator at a roadside check and the O-licence behind it.
  • Do not clear the code and carry on. The countdown restarts; the fault does not go away.
  • Do not top up from an open container of unknown age. Contaminated AdBlue causes more faults than failed pumps.

Getting it diagnosed properly

Fault codes narrow things down; they rarely name the part. A NOx sensor code can be a sensor, the wiring to it, a dosing fault upstream or an exhaust leak. Reading codes, live data and the system's own history together is what separates a repair from a parts swap.

Our truck diagnostics covers engine and ECU faults, emissions, AdBlue and SCR, DPF problems, ABS and EBS codes, and electrical fault finding. If the vehicle is also due an inspection or a test, it makes sense to do them in one visit — the ATF lanes and the workshop are on the same site.

Book in at Keighley

CFM runs a two-lane DVSA Authorised Testing Facility, a DVSA-approved tachograph centre and an IRTE-accredited workshop at Parkside Works, Parkwood Street, Keighley BD21 4PJ. We are open 07:00–17:00 Monday to Friday and 07:00–12:00 on Saturday, and we cover Airedale, Bradford, Wharfedale, Craven and Leeds.

Call 01535 662706 or send us an enquiry — tell us the vehicle and what you need, and we will confirm the earliest available slot.

Vehicle off the road? Let's get it moving.

Call the workshop or send us the details. We'll give you a clear quote and the earliest slot we can.

Call now Get a quote