Skip to content
CFM Limited logo

Tachographs

Tachograph downloads: 28 days, 90 days, and what to do when a unit fails

4 min read

Driver cards every 28 days, vehicle units every 90. Those two intervals are the whole of tachograph record keeping, and missing them is one of the easiest findings for an examiner to make.

The two intervals

DVSA's tachograph rules are direct about it: operators must download the vehicle unit every 90 days and the driver card every 28 days, and then analyse what comes out. Downloading and filing it unread satisfies the letter and none of the point.

Two more timings sit alongside those:

  • Drivers must return used analogue charts to the operator within 42 days
  • At the roadside, a driver must produce the current day plus the previous 28 calendar days — or 56 days for international journeys to and from an EU member country

The 28-day download interval and the 28-day production requirement are not the same thing, and conflating them is how operators end up with a gap. One is about your records; the other is about what is in the cab right now.

When a driver card fails

Lost, stolen, damaged or malfunctioning, the rules are specific and generous enough to keep the vehicle working.

  • The driver may continue for a maximum of 15 calendar days without the card — or longer if that is what it takes to get the vehicle back to base
  • Two printouts must be made, at the start and the end of the day, with the driver's details marked and signed
  • The problem must be reported and a replacement card applied for within 7 calendar days

Fifteen days of driving, seven days to apply. The application deadline is the shorter one and it is the one that gets missed.

When the tachograph itself fails

If the unit malfunctions, the driver makes a manual record — on an analogue record sheet or on printout paper — and reports the malfunction to the operator. The driver is also required to check, before using it, that the tachograph is correctly calibrated, by reading the plaque or interrogating the unit.

On replacement there is a rule worth knowing, because it catches operators out on older vehicles used only in the UK:

Faulty unitWhat it can be replaced with
Analogue or digitalLike for like, or better
Smart 1Must be a full or transitional smart 2

So a smart 1 failure is not a like-for-like swap. It is a step up, and it is worth knowing that before the vehicle is off the road waiting for a part.

Smart 2: the dates that have already passed

These are easy to lose track of, so in order:

  • 21 February 2024 — smart 2 required in all newly registered in-scope vehicles, whatever the journey type
  • 24 December 2025 — all newly registered goods vehicles must have a full smart 2. Transitional units already fitted to vehicles registered before this date do not have to be retrofitted
  • 1 July 2026 — a full smart 2 required in goods vehicles over 2.5 tonnes used on international journeys for hire and reward

The difference between full and transitional is the location verification facility — the transitional unit does not have Galileo in its software.

Two exclusions worth noting. Goods vehicles over 2.5 tonnes and under 3.5 tonnes used only in the UK do not need a tachograph at all. And on UK-only work, an original analogue, digital or smart 1 unit can still be used — until it fails, at which point the table above applies.

Calibration is a separate obligation

Downloading records and calibrating the unit are two different duties, and meeting one says nothing about the other. Statutory periodic calibration, recalibration after a change to tyre size or axle ratio, and the new plaque that goes with it are covered in our post on when tachograph calibration is due.

What an examiner is looking for

  • Downloads at the right intervals, with no gaps — a missing 90-day window is visible immediately
  • Evidence the data was analysed, and that infringements were raised with drivers
  • Manual records covering any period a unit or card was out of action
  • Charts collected within 42 days and accounted for
  • Drivers who can produce the right range at the roadside

The pattern is the same as it is for maintenance: the records are the evidence that the system works. Our post on O-licence maintenance records covers the other half of that paper trail.

Tachograph work at CFM

We are a DVSA-approved tachograph centre for analogue, digital and smart units — calibration, inspection, fault-finding and repair — open Monday to Saturday, and happy to book calibration alongside a safety inspection or an annual test so the vehicle makes one trip rather than two.

Book in at Keighley

CFM runs a two-lane DVSA Authorised Testing Facility, a DVSA-approved tachograph centre and an IRTE-accredited workshop at Parkside Works, Parkwood Street, Keighley BD21 4PJ. We are open 07:00–17:00 Monday to Friday and 07:00–12:00 on Saturday, and we cover Airedale, Bradford, Wharfedale, Craven and Leeds.

Call 01535 662706 or send us an enquiry — tell us the vehicle and what you need, and we will confirm the earliest available slot.

Vehicle off the road? Let's get it moving.

Call the workshop or send us the details. We'll give you a clear quote and the earliest slot we can.

Call now Get a quote